EUROPE

• ■ Improvement in excitation force

  When compared with the conventional i & J series, the A series increases the relative excitation force.

  ・Increased force per system power requirement
  ・Increased force per system mass
  ・Increased force per system size

  

• ■ Standard 76.2 mmp-p displacement
  *Only for A30, A45, A65, A74

  A-series has a displacement of 76.2 mmp-p (3 inch stroke) which gives good balance between specification of velocity, acceleration and displacement. This single system can be used in a very wide variety of tests.

  

• ■ Increase in frequency range

  In addition to the increased displacement of 76.2 mmp-p, the maximum frequency range is also increased when compared to the i, and J-series.

  

• ■ Introduction of new power module

  By developing a power amplifier that uses a new next generation Silicon Carbide power module, IMV has achieved low noise and high efficiency. All A-series models are equipped with this new power module as standard.

  

• ■ High velocity shock testing

  Where a test requires a high shock velocity, traditional shaker systems use a matching transformer to achieve the necessary higher armature voltage.
  Since IMV’s ECO-system has complete control over the field level, the field value can be adjusted to increase the maximum shock velocity capability of the system. By entering the specified shock profile into IMV’s K2 controller. The field level in the shaker is automatically adjusted to ensure that the required velocity is achieved. A-series (EM amplifier model) provides a maximum of 4.6 m/s shock velocity testing.

  

  i-series (conventional)	Model	i220/ SA1M
  	Rated Force Shock (kN)	16
  	Maximum Velocity Shock (m/s peak)	2.2
  	Maximum Displacement (mmp-p)	51
  	Maximum Load (kg)	Not achievable *not enough velocity and displacement

  J-series (conventional)	Model	No applicable product	J230/ SA3M	J240/ SA4M	J250/ SA6M	J260/ SA7M	No applicable product
  	Rated Force Shock (kN)	-	40	55	80	108	-
  	Maximum Velocity Shock (m/s peak)	-	2.4	2.4	2.4	2.4	-
  	Maximum Displacement (mmp-p)	-	100	100	100	100	-
  	Maximum Load (kg)	-	Not achievable *not enough velocity				-

  A-series	Model	A11/ EM1HAM	A22/ EM2HAM	A30/ EM3HAM	A45/ EM4HAM	A65/ EM5HAM	A74/ EM8HAM
  	Rated Force Shock (kN)	22 （16.5）	44 （36）	60 （50）	90 （80）	130 （120）	180 （160）
  	Maximum Velocity Shock (m/s peak)	2.5 （3.5）	2.5 （3.5）	2.5 （3.5）	2.5 （3.5）	2.5 （3.5）	2.5 （3.5）
  	Maximum Displacement (mmp-p)	51 （55）	51 （55）	76.2	76.2	76.2	76.2
  	Maximum Load (kg)	7	14	17	30	48	86

• ■ Lower power consumption

  In comparison with the same class of conventional systems (i,J-series), the A-series achieves lower power consumption. With an automatic energy-saving function increased energy saving is achieved across all force ranges.

  

• ■ International safety standards

  A-series complies with international safety standards.

  

SYSTEM MONITOR

Remote monitoring of the test status over the internet.

The status of the test, and the amplifier or shaker operation can be viewed on a remote PC using a standard internet browser.
Problems or errors are easily identified.

• 

  Home screen

• 

  Home screen(Error)

• 

  Eco screen

• 

  Camera screen

• 

  Chamber screen

•